Análise comparativa entre simuladores de linha de fluxo e diferenças finitas para um reservatório de petróleo submetido a injeção de água

Water injection is the most widely used method for supplementary recovery in many oil fields due to various reasons, like the fact that water is an effective displacing agent of low viscosity oils, the water injection projects are relatively simple to establish and the water availability at a relatively low cost. For design of water injection projects is necessary to do reservoir studies in order to define the various parameters needed to increase the effectiveness of the method. For this kind of study can be used several mathematical models classified into two general categories: analytical or numerical. The present work aims to do a comparative analysis between the results presented by flow lines simulator and conventional finite differences simulator; both types of simulators are based on numerical methods designed to model light oil reservoirs subjected to water injection. Therefore, it was defined two reservoir models: the first one was a heterogeneous model whose petrophysical properties vary along the reservoir and the other one was created using average petrophysical properties obtained from the first model. Comparisons were done considering that the results of these two models were always in the same operational conditions. Then some rock and fluid parameters have been changed in both models and again the results were compared. From the factorial design, that was done to study the sensitivity analysis of reservoir parameters, a few cases were chosen to study the role of water injection rate and the vertical position of wells perforations in production forecast. It was observed that the results from the two simulators are quite similar in most of the cases; differences were found only in those cases where there was an increase in gas solubility ratio of the model. Thus, it was concluded that in flow simulation of reservoirs analogous of those now studied, mainly when the gas solubility ratio is low, the conventional finite differences simulator may be replaced by flow lines simulator the production forecast is compatible but the computational processing time is lower.

Campo e contracampo : o encontro com o outro no filme Lavoura Arcaica

This dissertation aims to comprehend how we meet with the other at cinema. For this, it receives the doubt, the uncertainty, the way that the human being is unfinished as stance of observation. It takes into consideration the multiples social vectors, historical, subjective, temporal and cultural which constitute these phenomena. The cinema is used as a cognitive resource in order to incorporate the poetic and the imaginary, making possible not forgetting gestures and knowledge that hatch from sounds, colours, remembrances, images, words, social exchanges, cognitive reciprocity that allow us to think about the culture, the society and the communication. For this, it has as theoretical prerequisites ideas of double (myselfthe other) and effective participation (projection-identification) developed by Edgar Morin, as well as the idea of communication as possibility/impossibility of constructions of bonds with the other through the body, our primary media, concepts developed by Harry Pross and Norval Baitello Jr. The chosen film to analysis is Lavoura Arcaica, it is an emblematic movie in the discussion of the human condition and in the relationship between the man and its body, its desires, with its nature/culture ambivalence. About this film are made reflections about the process of activation of the double (myself-the other) in the searching for the other through cinematographically elements of construction, as: montage, direction, screenplay, actors, scenography, costumes and soundtrack. In conclusion, the cinema, when it allows the effective participation and provides t e experiment of the double, becomes a gateway line in the path to development of the alterity

Ciência como montagem, montagem como ciência

The thesis describes parallel possibilities between the knowledge built in theatre and in Science. The narrative is constructed through a reflexive observation of the process of making a threatical play, specifically O Tempo da Chuva by Grupo Beira de Teatro , in analogy to the process of making a scientific theory, specifically the one described by Werner Heisenberg in his book Physics and Beyond: encounters and conversations . It sets a dialog with authors/actors from various areas of knowledge, such as Edgar Morin, Werner Heisenberg, René Descartes, Paul Feyerabend, Paul Caro, Juremir Machado da Silva, Maria da Conceição de Almeida, Renato Ferracini, among others. It discusses the hypothesis that Science is the process of building and the theatrical process of building a play can also be systematized, likewise science. The thesis defends, as the complexities science may suggest, a method as a strategy. Developed throughout the process, such method could only be verified at the end, when the elements of the setting of atomic physics theories and theatre were correlated. Questions such as: the place of theatre and science in our contemporary society and the political and ethical role of artists and scientists are at the episthemological basis of this narrative which we have started, but it is not even close to a conclusion

Acoplador e linha de lâmina unilateral e bilateral com substrato fotônico

The aim of this work is to characterize and use the characteristic parameters of the planar structures constructed with fin lines looking for their applications in devices, using PBG Photonic Band Gap photonic materials as substrate, operating in the millimeter and optic wave bands.The PBG theory will be applied for the relative permittivity attainment for the PBG photonic substrate s and p polarizations. The parameters considered in the structures characterization are the complex propagation constant and the characteristic impedance of unilateral and bilateral fin lines that were obtained by the use of the TTL Transverse Transmission Line Method, together with the Method of the Moments. The final part of this work comprises studies related to the behavior of the asymmetric unilateral fin line coupler with photonic substrate. This research opens perspectives for new works in this modern area. Numerical results are shown by means of bi-dimensional and three-dimensional graphics. Conclusions and suggestions for future works are also presented

ISE-SPL: Uma abordagem baseada em linha de produtos de software aplicada à geração automática de sistemas para educação médica na plataforma E-learning

E-learning, which refers to the use of Internet-related technologies to improve knowledge and learning, has emerged as a complementary form of education, bringing advantages such as increased accessibility to information, personalized learning, democratization of education and ease of update, distribution and standardization of the content. In this sense, this paper aims to develop a tool, named ISE-SPL, whose purpose is the automatic generation of E-learning systems for medical education, making use of concepts of Software Product Lines. It consists of an innovative methodology for medical education that aims to assist professors of healthcare in their teaching through the use of educational technologies, all based on computing applied to healthcare (Informatics in Health). The tests performed to validate the ISE-SPL were divided into two stages: the first was made by using a software analysis tool similar to ISE-SPL, called SPLOT and the second was performed through usability questionnaires to healthcare professors who used ISESPL. Both tests showed positive results, proving it to be an efficient tool for generation of E-learning software and useful for professors in healthcare

Montagem e operação de um secador pneumático tipo flash

In this work, a pneumatic dryer has been designed and assembled in laboratory scale in order to study and evaluate configurations more efficient for application in drying of important materials of Northeast region in Brazil. The equipment was tested with drying of corn and rice grains, in conditions of temperature and air velocity at 80 oC and 35 m/s, respectively. For this type of dryer, it is recommended to work at temperatures above 200 °C and air velocity with higher dynamic pressure. However, even under operating conditions below what it is recommended, the results obtained with the pneumatic dryer were satisfactory. In addition, experiments of drying were performed by using a cabinet dryer (batch dryer) under the same conditions used in the pneumatic dryer. Flash one curves for the corn were fitted satisfactorily by applying of the Lewis model, while a better agreement was found for rice by using the Page model. The data obtained with both drying processes allowed to compare the performance between pneumatic and batch dryers. In respect to drying rate, the pneumatic dryer presented a similar performance to the batch dryer during processing with corn and a superior performance to the last one during processing with rice. Therefore, it was possible to verify that the pneumatic dryer assembled in this preliminar study can be applied for different materials and under different operating conditions

Monitoramento por dgps e análise dos processos erosivos da linha de costa na praia de Pirangi do Norte - Parnamirim / RN

Through out the course of a steady increase in search and recovery of space in the coastal zone, there is also an expanding concern about the erosion processes of this area. The main problem in coastal areas is that urbanization occurs in a disorderly fashion and unsustainable, further aggravating the problems of coastal dynamics. The study area of this work is located on the southern coast of Pirangi do Norte beach to about 20km south of Natal, capital of Rio Grande do Norte in the Parnamirim City. This area has the length of approximately 1km, divided into three sections (Western, Central and Eastern) with a morphology consisting of a tableland at the top, sea cliffs in the West and Central parts and sand dunes in the Eastern section, both vegetated, and a coastal plain on the inferior part associated with the presence of beach rocks. This study aimed to analyze the erosion processes operating in the excerpt of Pirangi do Norte beach and assess the feasibility of their monitoring making use of DGPS (Global Positioning System Differential mode). During the work it was carried out a physical description of the area through photo-interpretation and site survey after measurement of the shoreline in the period between November 2004 and November 2009 and beach profiles between August 2005 and July 2006. The analysis of the results of the annual surveys showed the occurrence of variations of the shoreline along the stretch traveled. Sites are identified in advancement coast from the sea and it was verified in loco the presence of erosion with deposition of materials on the lower part of the coastal bluff, the former position of the shoreline, showing a false notion of advancing it. This leads to the conclusion that the data collected in a survey of the shoreline should always be accompanied by photographic records of the local area and with the highest rate of erosion, thus avoiding the mistake of treating the deposit materials as evidence of progress coast. At the end of the study, after a review of various works to mitigate the erosion in the coastal zone, it is recommended to the area of study the adoption of an artificial feeding of the beach, aiming the minimization of the erosive effects of the tides. Moreover, it is suggested that even the continuity of monitoring, maintenance of existing vegetation and control of the occupation on the edge of sea cliffs

A perfeição da justiça em Platão uma análise comparativa entre a alegoria da linha dividida e os personagens d A República

The allegory of the divided line presents one structure that divides itself into four levels of reality. Two of them move in the world of appearances or opinion, and the others into the world of being or intelligibility: eikasia and pistis, and dianoia and noesis. The difficulty is the following: if there are four levels of reality each with their respective objects that are apprehended according to a type of knowledge involved, is there an interpretation of the justice according to each level? Accordingly, our intention, after presenting the types of knowledge in the allegory of the divided line, is to demonstrate how the justice is comprehended at each level of reality. We understand that Plato uses the characters to represent levels involving different types of knowledge. The characters are Cephalus, Polemarchus, Thrasymachus, Glaucon, Adimantus and Socrates, and the comprehension about what is the justice at each level follows what these characters understand justice to be

Montagem e construção de um magnetômetro a efeito Kerr magneto-óptico

n this master s dissertation a Kerr Magneto Optic s magnetometer effect was set up to do characterization of samples type films fine and ultra thin, these samples will be grown after the implementation of the sputtering technique at the magnetism laboratory of of this department. In this work a cooled electromagnet was also built the water and that it reaches close values to 10kOe with a gap of 22 mm including an area of uniform field of 25mm of diameter. The first chapter treats of the construction of this electromagnet from its dimensioning to the operation tests that involve measures of reached maximum field and temperature of the reels when operated during one hour. The second chapter is dedicated to the revision of the magnetism and the magnetization processes as well as it presents a theoretical base regarding the magnetic energies found in films and magnetic multilayer. In the sequence, the third chapter, is especially dedicated the description of the effects magneto opticians the effect kerr in the longitudinal, traverse and polar configurations, using for so much only the classic approach of the electromagnetism and the coefficients of Fresnel. Distinguished the two areas of observation of the effect regarding thickness of the film. The constructive aspects of the experimental apparatus as well as the details of its operation are explained at the room surrender, also presenting the preliminary results of the measures made in one serializes of permalloy films and concluding with the results of the characterization of the first films of iron and permalloy grown here at the theoretical and experimental physics department at UFRN

Padrão de distribuição e caracterização morfológica de fibras serotonérgicas nos núcleos da linha Média/ intralaminares do tálamo do mocó (Kerodon rupestris)

The midline/intralaminar nuclei form a remarkable group of nuclei of the medial and dorsal thalamus. The midline nuclei, in rats, comprises the paratenial nuclei (PT), paraventricular (PV), intermediodorsal (IMD), reuniens (Re) and rhomboid (Rh). The intralaminar nuclei comprises the central medial (CM), paracentral (PC), central lateral (CL) and parafascicular (PF). Such nuclei have dense serotonergic innervation originating from the brainstem, especially from the so-called ascending activation system. These nuclei, in turn, send projections to various cortical and subcortical areas, specifically to limbic areas, which suggests the important role of this neurotransmitter in the limbic circuitry. The aim of this study was to characterize the distribution pattern and morphology of serotonin fibers in the nuclei of the midline and intralaminar thalamic of rocky cavy (Kerodon rupestris), a tipical rodent from brazilizan northeast. To reach this aim we used four rock cavies adults. Following the transcardially perfusion with paraformaldehyde and brain microtomy steps was performed immunohistochemistry for serotonin (5-HT), Nissl technique and subsequent achievement and image analysis to characterize the cytoarchitecture of these nuclei and the serotonergic fibers visualized. An analysis was made of Relative Optical Density (ROD) to semi-quantify the concentration of serotonin fibers in the areas of interest. Thus, we observed a cytoarchitectonic arrangement of these nuclei similar to that found in rats. In case of fibers distribution, those immunoreactive to 5-HT were presented in a higher concentration according as ROD in the midline nuclei relative to intralaminar; Re being the core which has a higher pixel value followed by the PV , Rh, IMD and PT. In intralaminar CL showed higher pixels, followed by nuclei CM, PC and PF. The serotonergic fibers were classified as number of varicosities and axon diameter, therefore find three types of fibers distributed through this nuclear complex: fibers rugous, granular and semi-granular. In PV fibers predominated rugous; in PT fibers predominated granular; IMD, CL and PF fibers were represented by semi-granular and Re, Rh, PC and CM fibers showed granular and semi-granular. Morphological characterization of serotonergic fibers and differences in density between the nuclei may suggest different patterns of synaptic organization of this neurotransmitter beyond confirming his large repertoire functional

GingaForAll: linha de Produtos do Middleware Ginga

Many challenges have been imposed on the middleware to support applications for digital TV because of the heterogeneity and resource constraints of execution platforms. In this scenario, the middleware must be highly configurable so that it can be customized to meet the requirements of applications and underlying platforms. This work aims to present the GingaForAll, a software product line developed for the Ginga - the middleware of the Brazilian Digital TV (SBTVD). GingaForAll adds the concepts of software product line, aspect orientation and model-driven development to allow: (i) the specification of the common characteristics and variables of the middleware, (ii) the modularization of crosscutting concerns - both mandatory and concepts variables - through aspects, (iii) the expression of concepts as a set of models that increase the level of abstraction and enables management of various software artifacts in terms of configurable models. This work presents the architecture of the software product line that implements such a tool and architecture that supports automatic customization of middleware. The work also presents a tool that implements the process of generating products GingaForAll

BMMobile: uma linha de produtos para dimensionamento de bombeio mecânico em dispositivos móveis

With the increase of processing ability, storage and several kinds of communication existing such as Bluetooth, infrared, wireless networks, etc.., mobile devices are no longer only devices with specific function and have become tools with various functionalities. In the business field, the benefits that these kinds of devices can offer are considerable, because the portability allows tasks that previously could only be performed within the work environment, can be performed anywhere. In the context of oil exploration companies, mobile applications allow quick actions could be taken by petroleum engineers and technicians, using their mobile devices to avoid potential catastrophes like an unexpected stop or break of important equipment. In general, the configuration of equipment for oil extraction is performed on the work environment using computer systems in desktop platforms. After the obtained configuration, an employee goes to equipment to be configured and perform the modifications obtained on the use desktop system. This management process equipment for oil extraction takes long time and does not guarantee the maintenance in time to avoid problems. With the use of mobile devices, management and maintenance of equipment for oil extraction can be performed in a more agile time once it enables the engineer or technician oil can perform this configuration at the time and place where the request comes for example, near in the oil well where the equipment is located. The wide variety of mobile devices creates a big difficulty in developing mobile applications, since for one application can function in several types of devices, the application must be changed for each specific type of device, which makes the development quite costly. This paper defines and implements a software product line for designing sucker-rod pumping systems on mobile devices. This product line of software, called BMMobile, aims to produce products that are capable of performing calculations to determine the possible configurations for the equipment in the design suckerrod pumping, and managing the variabilities of the various products that can be generated. Besides, this work performs two evaluations. The first evaluation will verify the consistency of the products produced by the software product line. The second evaluation will verify the reuse of some products generated by SPL developed

Integrais de linha intervalares: fundamentos e aplicações

A necessidade de uma precisão e de uma aproximação dos resultados numéricos zeram com que diversas teorias surgissem: dentre elas, destacamos a Matemática Intervalar. A Matemática Intervalar surgiu na década de 60 com os trabalhos de pesquisa de Moore (MOORE, 1959) , em que ele propôs trabalhar com uma Matemática baseada na noção de intervalo real e não mais com um número como aproximação. Com isso, surgiu a necessidade de revisitar e reformular os conceitos e resultados da Matemática Clássica utilizando como base a noção de intervalo de Moore. Uma das áreas da Matem ática Clássica que tem tido muitas aplicações em engenharias e ciências é a Análises Numérica, onde um dos seus pilares é o Cálculo Integral e em particular as integrais de linha. Assim, é muito desejável se ter um cálculo integral dentro da própria Matemática Intervalar. No presente trabalho apresenta-se uma noção de Integral de Linha Intervalar baseada na extensão de integração proposta por Bedregal em (BEDREGAL; BEDREGAL, 2010). Para a fundamentação apresenta-se incialmente uma introdução sobre a pespectiva em que o trabalho foi realizado, considerando alguns aspectos histórico-evolutivos da Matemática Clássica. Os conceitos de Integrais de Linha Clássica, bem como algumas das suas aplicações mais importantes. Alguns conceitos de Matemática Intervalar necessários para o entendimento do trabalho. Para nalizar propomos uma aplicação da integral de linha em um experimênto clássico da mecânica quântica (a difração de um elétron em uma fenda) que graças ao fato de ser a Matemática Intervalar utilizada, nos dá um foco mais detalhado e mais próximo da realidade

A predominância do filtro ambiental local na montagem de uma floresta tropical de ambiente estressante

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise da sobre-reação e sub-reação nos ativos de primeira e segunda linha do mercado acionário brasileiro

The Behavioral Finance develop as it is perceived anomalies in these markets efficient. This fields of study can be grouped into three major groups: heuristic bias, tying the shape and inefficient markets. The present study focuses on issues concerning the heuristics of representativeness and anchoring. This study aimed to identify the then under-reaction and over-reaction, as well as the existence of symmetry in the active first and second line of the Brazilian stock market. For this, it will be use the Fuzzy Logic and the indicators that classify groups studied from the Discriminant Analysis. The highest present, indicator in the period studied, was the Liabilities / Equity, demonstrating the importance of the moment to discriminate the assets to be considered "winners" and "losers." Note that in the MLCX biases over-reaction is concentrated in the period of financial crisis, and in the remaining periods of statistically significant biases, are obtained by sub-reactions. The latter would be in times of moderate levels of uncertainty. In the Small Caps the behavioral responses in 2005 and 2007 occur in reverse to those observed in the Mid-Large Cap. Now in times of crisis would have a marked conservatism while near the end of trading on the Bovespa speaker, accompanied by an increase of negotiations, there is an overreaction by investors. The other heuristics in SMLL occurred at the end of the period studied, this being a under-reaction and the other a over-reaction and the second occurring in a period of financial-economic more positive than the first. As regards the under / over-reactivity in both types, there is detected a predominance of either, which probably be different in the context in MLCX without crisis. For the period in which such phenomena occur in a statistically significant to note that, in most cases, such phenomena occur during the periods for MLCX while in SMLL not only biases are less present as there is no concentration of these at any time . Given the above, it is believed that while detecting the presence of bias behavior at certain times, these do not tend to appear to a specific type or heuristics and while there were some indications of a seasonal pattern in Mid- Large Caps, the same behavior does not seem to be repeated in Small Caps. The tests would then suggest that momentary failures in the Efficient Market Hypothesis when tested in semistrong form as stated by Behavioral Finance. This result confirms the theory by stating that not only rationality, but also human irrationality, is limited because it would act rationally in many circumstances